Lantronix Open-Q 410 User Manual Download Page 33

Page: 33 / 38

4: Open-QTM 410 Carrier Board

Open-Q 410 Dev Kit User Guide

Description

Signal Name Pin #

Pin # Signal Name

Description

NC. Connected to test point

TP601.

JTAG_RTCK

GND

Output. Connected to

APQ8016E TDO pin.

JTAG_TDO

GND

Input. Connected to

APQ8016E SRST_N pin.

JTAG_SRST_N

GND

Pulled to GND via 4.7K

resistor.

GND

Pulled to GND via 4.7K

resistor.

GND

JTAG_DET_N

Input. Connected to GND by

JTAG module. Used to detect

the presence of a connected

JTAG module.

4.11 Audio Connectors

The Open-Q

410 Development Kit has several audio connectors that are described in this section. The

audio codec functionality is contained with the APQ8016E CPU and PM8916 PMIC. The table below

describes the audio path routing on the Open-Q

410 development kit.

Table 9 – Audio Path Connections

Function

Signal Name

Description

Digital MIC

DMIC0_CLK/DATA

Connected to Digital Mic Header (J1104). Also usable

as BLSP1.

MIC1 Input

CDC_MIC1_P

Connected to Stereo Line Input jack (J1101)

MIC2 Input

CDC_MIC2_P

Connected to Headset jack (J1105)

MIC3 Input

CDC_MIC3_P

Connected to Stereo Line Input jack (J1101)

Earpiece Output

CDC_EAR_N/P

Connected to speaker connector (J1102).

Headphone Stereo Output

CODEC_FLT_HPH_L

Connected to Headset jack (J1105)

Speaker Output (Class D)

SPKR_OUT_N/P

Connected to speaker connector (J1103).

4.11.1

Audio 3.5mm Jacks

There are two 3.5mm audio jacks on the carrier board as shown below. Connector J1105 is configured for use

with a typical TRRS Android headset jack. Connector J1101 is wired for use as a stereo line input.

Summary of Contents for Open-Q 410







































Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands

Lantronix Open-Q 410, User Manual

Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands