Lantronix Open-Q 410 User Manual Download Page 24

Page: 24 / 38

4: Open-QTM 410 Carrier Board

Open-Q 410 Dev Kit User Guide

4.5.2 Open-Q

Carrier Board Rev 0200

The Rev 0200 Open-Q

410 carrier board has two MIPI CSI camera connectors: J1401 and J1501. The two

JAE FI-RE41S-VF 41-pins connectors are shown in the figure below.

Figure 11 – MIPI CSI Camera Connectors on Rev 0200 CB

NOTE:
The MIPI CSI0 connector (J1401) has a 4-lane MIPI interface, while the MIPI CSI1 connector (J1501) only

has a 2-lane MIPI interface.

Table 5 – MIPI CSI Camera Connector Pinout (For Rev 0200)

Pin #

J1401

J1501

Description

23/24

MIPI_C

SI0_CL

K_N/P

MIPI_CSI1_CLK_N/P

Input. MIPI CSI0 / CSI1 clock lane

20/21

MIPI_C

SI0_LA

NE0_N/

MIPI_CSI1_LANE0_N/P

Input. MIPI CSI0 / CSI1 data lane 0

26/27

MIPI_C

SI0_LA

NE1_N/

MIPI_CSI1_LANE1_N/P

Input. MIPI CSI0 / CSI1 data lane 1

29/30

MIPI_C

SI0_LA

NE2_N/

Not Available (N/C)

Input. MIPI CSI0 data lane 2

33/32

MIPI_C

SI0_LA

NE3_N/

Not Available (N/C)

Input. MIPI CSI0 data lane 3

This pair’s order is swapped on purpose

CSI0_R

ST_N

(APQ80

16E

GPIO

35)

CSI1_RST_N

(APQ8016E GPIO 28)

Output. Camera reset.

CSI0_P

WDN

CSI1_PWDN

Output. Camera power down.

Summary of Contents for Open-Q 410







































Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands

Lantronix Open-Q 410, User Manual

Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands