Lantronix Open-Q 410 User Manual Download Page 37

Page: 37 / 38

5: Output Display Options

Open-Q 410 Dev Kit User Guide

5 Output Display Options

The Open-Q

410 development kit can be purchased with two output display options: an on-board display or

an HDMI output. Both of these options are connected to the carrier board display connector described above.
Please visit:

http://shop.intrinsyc.com/collections/dragonboard-accessories

for more information.

5.1 On-Board Display

There are two optional on-board displays supported by the Open-Q 410:

1. 4.46” FWVGA MIPI DSI LCD (Manufactured by Truly) with capacitive multi-touch
2. 4.5” FWVGA MIPI DSI LCD (Manufactured by OSD Displays) with capacitive multi-touch

Option 1: 4.46” panel manufactured by Truly, with an integrated capacitive touch panel. Detailed specifications

of this display board:

•

Model No: TDO-FWVGA0446G00002

•

Resolution: FWVGA (480x854xRGB)

•

Display Controller: Himax HX83796C

Support DSI Version 1.10

Support D-PHY version 1.10

•

Touch Controller: Synaptic S3202 Multi Touch Capacitive with HW buttons

•

Interface: MIPI DSI (2 data lanes)

Figure 20 – Truly FWVGA Panel

Summary of Contents for Open-Q 410







































Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands

Lantronix Open-Q 410, User Manual

Search results

Summary of Contents for Open-Q 410

Reviews:

Related manuals for Open-Q 410

Brands by name

Popular brands