Lantech LES-2400-RPS User Manual Download Page 47

Page: 47 / 99

Advanced Configuration

Broadcast Storm Filter

This tab allows users to enable the broadcast storm filter for the specific packet type.

Tick the checkboxes respectively to enable the filters.



Flooded Unicast/Multicast Packets:

When this check box is ticked, the switch

will filter the packet type of

Flooded Unicast/Multicast



Control Packets:

When this checkbox is ticked, the switch will filter the

Control

packet.



IP Multicast Packets:

When this checkbox is ticked, the switch will filter the

Multicast

packet.



Broadcast Packets:

When this checkbox is ticked, the switch will filter the

Flooded Unicast/Multicast

packet.



Broadcast Storm Rate:

Users can set theingress filtering rate ranging from 1/2 to

1/16.



And then, click Apply to have the configuration take effect.

Broadcast Storm Filter

Summary of Contents for LES-2400-RPS




































































































Search results

Summary of Contents for LES-2400-RPS

Reviews:

Related manuals for LES-2400-RPS

Brands by name

Popular brands

Lantech LES-2400-RPS, User Manual

Search results

Summary of Contents for LES-2400-RPS

Reviews:

Related manuals for LES-2400-RPS

Brands by name

Popular brands