Lantech LES-2400-RPS User Manual Download Page 17

Page: 17 / 99

3. Network Application

This section provides you a few samples of network topology in which the Switch is

used. In general, the 3-slot intelligent chassis switch is designed as a segment switch.

That is, with its large MAC address table (8K-entry) and high performance, it is ideal for

interconnecting networking segments.

PCs, workstations, and servers can communicate each other via the 3-slot intelligent

chassis switch. The switch automatically learns node addresses, which are

subsequently used to filter and forward all traffic based on the destination address.

By using the Gigabit mini-GBIC port for long distance up-link, the switch can connect

with another switch or hub to interconnect other small-switched workgroups to form a

larger switched network. The figure below is an example application topology.

The example of application topology

Summary of Contents for LES-2400-RPS




































































































Search results

Summary of Contents for LES-2400-RPS

Reviews:

Related manuals for LES-2400-RPS

Brands by name

Popular brands

Lantech LES-2400-RPS, User Manual

Search results

Summary of Contents for LES-2400-RPS

Reviews:

Related manuals for LES-2400-RPS

Brands by name

Popular brands