manualshive.com logo in svg

L&L EASY-FIRE e18S, Assembling

The L&L EASY-FIRE e18S comes with a comprehensive assembling manual available for free download from our website. Clear and concise instructions allow users to effortlessly set up their e18S kiln and start firing ceramics with utmost ease. Enhance your pottery experience with this user-friendly product.

Share
Download
background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf 

3/1/2007 Rev 1.3 

Page 

 

2007  

 

L&L Kiln Mfg, Inc.  505 Sharptown Rd, Swedesboro NJ 08085  P:856.294.0077  F:856.294.0070  [email protected]   hotkilns.com 

  

Power Terminal Strip is shown :

4)  Remove  wires  numbers  1  through  6  from  both 
sides of the Thermocouple Terminal Strip . 

The Thermocouple Terminal Strip:

5)  Remove  the  green  ground  that  connects  the  front 
panel to the rear panel .

Removing the ground wire:

6) Tilt the control panel halfway back to its original 
position  and  gently  pull  the  panel  from  the  element 
box and set aside . It will take a combination of pulling 
slightly  up  and  slightly  out  to  disengage  the  control 
panel from the element terminal box . 

Removing the panel:

REMOVING ELEMENT COVER BOX

If  you  prefer  you  can  remove  the  box  using  the 
method shown on page 7 instead .

1) Remove the three screws on the right hand side of 
the element box and set them aside . 

Removing the right hand screws :

2)  Loosen  the  3  screws  on  the  left  hand  side  of  the 
element box but leave them in place . Loosen them to 
about a ½ inch .  

Loosen the left hand side 

ASSEMBLING YOUR L&L EASY-FIRE KILN

Summary of Contents for EASY-FIRE e18S


















Reviews:

No comments

Related manuals for EASY-FIRE e18S

Brands by name

Popular brands

Load more brands