manualshive.com logo in svg

L&L EASY-FIRE e18S, Assembling

The L&L EASY-FIRE e18S comes with a comprehensive assembling manual available for free download from our website. Clear and concise instructions allow users to effortlessly set up their e18S kiln and start firing ceramics with utmost ease. Enhance your pottery experience with this user-friendly product.

Share
Download
background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf 

3/1/2007 Rev 1.3 

Page 

 

2007  

 

L&L Kiln Mfg, Inc.  505 Sharptown Rd, Swedesboro NJ 08085  P:856.294.0077  F:856.294.0070  [email protected]   hotkilns.com 

  

3) Attach  the  flexible  vent  tube  to  the  outlet  of  the 
vent collection box . This takes some patience to get 
the flexible tube around the fitting .

Installing the flexible duct onto the Bypass 
Collection Box of the Vent-Sure Vent System:

4)  Fit  the  rubber-plastic  feet  over  the  bottom  of  the 
legs . The stand is now fully assembled . 

The fully assembled stand:

REMOVING THE LID

The  next  step  is  to  remove  the  lid  from  the  kiln .  
Remove the cotter pin, then the hinge pin, pull the bar 
out  and  remove the spring .  Set  them aside . Remove 
the lid from the kiln .

The  hinge  is  shipped  assembled  (without  the 
spring engaged). This way you can see how it all 
goes back together. 

Now you can remove the top :

ASSEMBLING YOUR L&L EASY-FIRE KILN

Summary of Contents for EASY-FIRE e18S


















Reviews:

No comments

Related manuals for EASY-FIRE e18S

Paragon MagicFuse Instructions/Service Manual preview
MagicFuse
Brand: Paragon Pages: 8

Brands by name

Popular brands

Load more brands