L&L EASY-FIRE e18S Assembling Download Page 3 | Manualshive

Page: 3 / 17

background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf

3/1/2007 Rev 1.3

Page 3



2007

L&L Kiln Mfg, Inc. 505 Sharptown Rd, Swedesboro NJ 08085 P:856.294.0077 F:856.294.0070 [email protected] hotkilns.com

d) a pair of temperature resistant gloves

For an e18T:

a) two 15-1/2'' full round shelves
b) four 15-1/2'' half shelves
c) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
d) five pounds of Cone 10 kiln wash
e) dark viewing glasses
d) a pair of temperature resistant gloves

For an e18T-3:

a) two 15'' full round shelf
b) four 15'' half shelves
c) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
d) five pounds of Cone 10 kiln wash
e) dark viewing glasses
d) a pair of temperature resistant gloves

For an e23S:

a) One 21'' full round shelf
b) four 21'' half shelves
c) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
d) five pounds of Cone 10 kiln wash
e) dark viewing glasses
d) a pair of temperature resistant gloves

For an e23S-3

:

a) One 20'' full round shelf
b) four 20'' half shelves
c) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
d) five pounds of Cone 10 kiln wash
e) dark viewing glasses
d) a pair of temperature resistant gloves

For an e23T:

a) two 21'' full round shelves
b) four 21'' half shelves
c) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
d) five pounds of Cone 10 kiln wash
e) dark viewing glasses
d) a pair of temperature resistant gloves

For an e23T-3:

a) two 20'' full round shelf
b) four 20'' half shelves
c) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts

d) five pounds of Cone 10 kiln wash
e) dark viewing glasses
d) a pair of temperature resistant gloves

For an e28S-3:

a) six 26'' half shelves
b) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
c) five pounds of Cone 10 kiln wash
d) dark viewing glasses
e) a pair of temperature resistant gloves

For an e28T-3:

a) eight 26'' half shelves
b) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
c) five pounds of Cone 10 kiln wash
d) dark viewing glasses
e) a pair of temperature resistant gloves

Below is a picture of the cardboard insert with a
shelf  kit  and  Vent-Sure  system  enclosed.  NOTE:
Depending  on  where  you  bought  your  kiln  your
vent  system  and/or  kiln  furniture  may  arrive  in
separate boxes.

ASSEMBLING YOUR L&L EASY-FIRE KILN

«
1
2
3
4
5
...
»

Summary of Contents for EASY-FIRE e18S


















Reviews:

No comments

Related manuals for EASY-FIRE e18S

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands