L&L EASY-FIRE e18S Assembling Download Page 2 | Manualshive

Page: 2 / 17

background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf

3/1/2007 Rev 1.3

Page 2



2007

L&L Kiln Mfg, Inc. 505 Sharptown Rd, Swedesboro NJ 08085 P:856.294.0077 F:856.294.0070 [email protected] hotkilns.com

ASSEMBLING YOUR L&L EASY-FIRE KILN

UNPACKING

Inspect for visible damage

The  carton  should  arrive  without  visible  damage .  If
the carton was damaged in transit, you should either
refuse  shipment  or  unpack  the  kiln  in  the  drivers
presence  in  order  to  file  a  damage  report  with  the
freight  company .

Call our office immediately if

there is a problem . SAVE ALL MATERIALS
UNTIL YOU ARE SURE YOU WON'T NEED
THEM . AT THE VERY LEAST NOTE DAMAGE
ON THE BILL- OF-LADING - WITHOUT THIS
YOU HAVE NO PROTECTION!

Below is a picture of how your kiln should arrive:

Remove Top from Carton

1) Remove the packing slip from the packing list
enclosed envelope, as well as the kiln set up instruc-
tions from the large envelope that is on the side of the
kiln carton .

2) Cut the banding around the kiln box and remove
the top .

3) You are looking at the heavy duty top of the kiln
stand . Remove it and set it off to the side .

Below is the first thing you will see when you
open the box - the top of the stand:

Unpack Instructions, Vent and Furniture Kit

1) Remove the corrugated pad from the inside of the
carton .

2) For all kilns you will find the following items:

a) spring hinge tool
b) instruction manual
c) stand legs with the mounting hardware
d) Training Video

3) If you ordered a Vent-Sure vent system you will
find the following items inside the cardboard insert:

a) flexible ductwork
b) bypass collection box
c) galvanized 90 degree elbow
d) vent motor with bracket that holds it to the wall

4) If you ordered the Furniture/Accessory kit you will
find the following:

For an e18S:

a) One 15-1/2'' full round shelf
b) four 15-1/2' half shelves
c) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
d) five pounds of Cone 10 kiln wash
e) dark viewing glasses
d) a pair of temperature resistant gloves

e18S-3

:

a) One 15'' full round shelf
b) four 15'' half shelves
c) six each 1/2'', 1'', 2'', 4'', 6'' and 8'' square posts
d) five pounds of Cone 10 kiln wash
e) dark viewing glasses

«
1
2
3
4
...
»

Summary of Contents for EASY-FIRE e18S


















Reviews:

No comments

Related manuals for EASY-FIRE e18S

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands