manualshive.com logo in svg

L&L EASY-FIRE e18S, Assembling

The L&L EASY-FIRE e18S comes with a comprehensive assembling manual available for free download from our website. Clear and concise instructions allow users to effortlessly set up their e18S kiln and start firing ceramics with utmost ease. Enhance your pottery experience with this user-friendly product.

Share
Download
background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf 

3/1/2007 Rev 1.3 

Page 1

 

2007  

 

L&L Kiln Mfg, Inc.  505 Sharptown Rd, Swedesboro NJ 08085  P:856.294.0077  F:856.294.0070  [email protected]   hotkilns.com 

  

13) Push the spring into one of the two slotted holes 
on the side of the large hinge piece . The slot closest to 
the kiln will put more tension on the spring . (Note - it 
is hard to get the spring into this slot when working 
from above) .

Below is a view from the top looking down into 
the hinge box. NOTE: When removing the hinge 
- use the reverse procedure and be sure to use 
the special tool provided.

13) The hinge is now operational .  

14) Raise and lower the hinge a few times . 

15) Double check to make sure that each end of the 
spring  is  through  the  appropriate  hole  in  the  ring 
hinge piece .  

16) Open the lid to the full open position and insert the 
safety pin to keep the lid locked in the up position .

17) You are now ready to reassemble the panel onto 
the kiln .

REASSEMBLING THE CONTROL 
PANEL

1)  Take  the  Control  Box  and  Element  Cover  Box 
Assembly and place it on the screws on the 

left 

hand 

side of the element connection terminals (facing from 
the front) .

2)  Push  the  whole  assembly  off  to  the  side  left  side 
slightly  so  you  can  access  the  wires  and  push  them 
through the holes .

ASSEMBLING YOUR L&L EASY-FIRE KILN

Summary of Contents for EASY-FIRE e18S


















Reviews:

No comments

Related manuals for EASY-FIRE e18S

Brands by name

Popular brands

Load more brands