manualshive.com logo in svg

L&L EASY-FIRE e18S, Assembling

The L&L EASY-FIRE e18S comes with a comprehensive assembling manual available for free download from our website. Clear and concise instructions allow users to effortlessly set up their e18S kiln and start firing ceramics with utmost ease. Enhance your pottery experience with this user-friendly product.

Share
Download
background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf 

3/1/2007 Rev 1.3 

Page 1

 

2007  

 

L&L Kiln Mfg, Inc.  505 Sharptown Rd, Swedesboro NJ 08085  P:856.294.0077  F:856.294.0070  [email protected]   hotkilns.com 

  

3)  Push  the  Element  Cover  Box  up  against  the  kiln 
and position it over the screws through the large part 
of the tear-drop holes . Tighten the screws .

4) Attach  all  the  wires  to  their  proper  place  on  the 
terminal boards .

5) Close the Control box and screw in the two screws 
that hold it in place at the top of the Element Cover 
Box .

If  you  removed  the  panel  separate  from  the 
element cover box

1) Take the element terminal box and place it on the 
screws on the 

left 

hand side of the element connection 

terminals (facing from the front) .  

2)  Gently  push  the  right  side  of  the  element  cover 
box open enough to allow access to feed the element 
and thermocouple connection wires through the same 
holes that you previously removed them from . 

3) Take the 3 screws that you removed from the right 
side of the element cover box and replace and tighten 
them .  

Below:

4) Next tighten the 3 screws on the left hand side of 
the element cover box .  

5) Reconnect the wires to the appropriate numbered 
terminals . 

6) You are now ready to reattach the hinge portion of 
the dynatrol panel .

ASSEMBLING YOUR L&L EASY-FIRE KILN

Summary of Contents for EASY-FIRE e18S


















Reviews:

No comments

Related manuals for EASY-FIRE e18S

Brands by name

Popular brands

Load more brands