background image

13

Cleaning and Sanitizing Nozzles

1.  Disconnect power, so as to not activate valve while cleaning.
2.  Remove nozzle by twisting counter clockwise and pulling 

down.

3.  Remove diffuser by pulling down.
4.  Rinse nozzle and diffuser with warm water.
5.  Wash nozzle and diffuser with cleaning solution then  

immerse in sanitizing solution and let sit for fifteen (15) 

minutes. 

6.  Set nozzle and diffuser aside and let air dry. 

DO NOT

 rinse 

with water after sanitizing. 

7.  Reconnect diffuser and nozzle.
8.  Connect power.
9.  Taste the drink to verify that there is no off-taste. If off-taste 

is found, flush syrup system again.

A

B

C

A. Nozzle

B. Diffuser

C. Soda Lever

 

Following sanitization, rinse with end-use product  

 

until there is no aftertaste. Do not use a fresh water    

 

rinse. This is a NSF requirement. Residual sanitizing    

 

solution left in the system creates a health hazard.

CAUTION

Ice Chute Cleaning

1.  Turn off power to the dispenser.
2.  Remove Merchandiser.
3.  Remove Ice Chute Lever, then remove Splash Plate          

Assembly by lifting it up and out from the dispenser face.

4.  Remove the Ice Chute Assembly base by removing the four 

(4) screws that attach it to the unit.

5.  Prepare the Cleaning Solution.
6.  Soak the Ice Chute Assembly in the solution.
7.  Rinse and dry the  Ice Chute Assembly thoroughly.
8.  Reinstall the Ice Chute Assembly.
9.  Reinstall Merchandiser and Splash Plate.
10.  Reconnect power to the dispenser.

 

It is recommended to perform this procedure monthly, 

 

or more often if desired. Use the cleaning solution 

 

described above. An alternate solution of one part 

 

water to one part vinegar may be used to remove 

 

water spots and calcium deposits.

NOTE

 

Always remove the ice chute lever before removing 

 

the splash plate.

NOTE

     

 

To prevent possible harm to the environment from improper disposal, recycle the unit by locating   

 

   

an authorized recycler or contact the retailer where the product was purchased. Comply with local  

 

   

regulations regarding disposal of the refrigerant and insulation.

   

Dispenser Disposal

Summary of Contents for Bevariety ACIB Series

















Reviews: