background image

7

DISPENSER INSTALLATION HIGHLIGHTS

This unit has been factory sanitized per Lancer specifications.

Listed below are six critical elements which will aid in a successful installation.
1.   Fill water bath until water overflows from tank overflow tube.

2.   The carbonator pump motor must be disconnected from the power supply (see Section 1.7) prior to connection to 

water supply for initial build up of ice bank. Failure to do so will result in automatic shut off of carbonator (see item 

6 below) or damage to the pump.

3.   If this dispenser is installed in an area that is susceptible to ±10% variation of the nominal line voltage, consider  

installing a surge protector or similar protection device.

4.   There is a five (5) minute delay which prevents the compressor and condenser fan from starting until the delay 

has lapsed. If electrical current is interrupted, there is always a five (5) minute delay before the compressor starts.

5.   Supply Water Pressure: Minimum - 25 PSI (0.172 MPA); Maximum - 50 PSI (0.345 MPA);  If pressure is over 50 

PSIG (0.345 MPA), a water pressure regulator must be used.

6.   On units with the built in water regulator, the regulator must be removed if inlet water pressure is less than 25 

PSIG. 

(0.172 MPA)

PUNTOS IMPORTANTES EN LA UNIDAD DISPENSADORA 

Esta unidad ha sido saneada en fabrica por las especificaciones de Lancer.

A continuacion se relacionan 6 puntos importantes para una connecta instalacion.
1.   Llene  el  bano-Maria  hasta  que  el  agua  se  desborde  sobre  el  tubo  que  controla  la  derrama  del  tanque.

2.   El motor de la bomba del carbonatador debe desconectarse electricamente (Ver Manual - Seccion 1.7) antes 

de conectar el suministro de agua para la formacion inicial del banco de hielo. De no hacerse esto resultaria en 

un bloqueo automatico del carbonatador (ver abajo el punto 6) o en danos a la bomba.

3.   Si la unidad va a ser instalada en un area en la que puedan darse variaciones de voltage de + 6 - 10% de su 

valor nominal, se debe considerar la conveniencia de instalar un estabilizador de corriente o sistema de 

proteccion similar.

4.   Hay una demora de 5 minutos que evita que el compresor y el abanico del condensador arranquen hasta pasado 

ese tiempo. Si hay algun corte en la corriente electrica siempre se producira esa demora de 5 minutos antes de 

arrancar el compresor.

5.   Presión de suministro del agua de red: Minimo 25 PSI (0.172 MPA); Maximo 50 PSI (0.345 MPA). En unidades 

sin regulador de presión incorporado, si la presión del agua es superior a 50 PSIG (0.345 MPA) se debe usar un 

regulador de presión.

6.   En unidades con regulador de presión incorporado, el regulador debe der eliminado cuando la presión de entrada 

de agua sea inferior a 25 PSIG (0.172 MPA).

REGLES DE SECURITE POUR L’NSTALLATION DU DISTRIBUTEUR DE SODAS 

La proprètè da cet ensamable est assurè à I’usine sulvant les spècifications èmis par Lancer .

Il est essentiel de respecter les 6 points suivants pour l’installation de l’appareil:
1.   Remplir le bain-Maire jusqu’a ce que l’eau dèborde par le tuyau de trop-plein du rèservoir.

2.   Le moteur de la pompe du carbonateur doit etre dèbranchè de l’alimentation èlectrique (Voir le manuel, 

Section 1.7) avant l’arrivèe de l’eau pour la formation initiale de la glace. Oublier ou nègliger cette opèration 

provoquera l’arret automatique du carbonateur (voir le point 6 cidessous) ou causera des dommages à la pompe.

3.   Si le distributeur es installè dans une zone ou la tension èlectrique nominale est susceptible de variations de (+) 

10%, il est conseillè d’installer un appaeil de protection contre les sautes de courant.

4.   Un d’lai de 5 minutes empeche le compresseur et la ventilation du condesateur de se mettre en marche avant 

que ce lees de temps ne se soit ècoulè. Lorsque le courant èlectrique es interrompu, il y a toujours un dèlai de 5 

minutes avant que le presseur ne se mette en.

5.   Pression de l’eau: Minimum 25 PSI (0.172 MPA); Maximo 50 PSI (0.345 MPA). Sur les unitès qui n’ont pas de 

règulateur de pression d’eau incorprè, si la pression d’H2O est supèrieure à 50 PSIG (0.345 MPA), un règulateur 

de pression d’eau doit etre utilsisè.

6.   Sur les unitès avec règulateur d’eau incorporè, le règulateur doit etre enlevè si la pression d’arrivve est inferièure 

à 25 PSIG (0.172 MPA)

!

!

!

!

!

!

Summary of Contents for 605





































Reviews: