background image

TROUBLE

CAUSE

REMEDY

13

8.7

Syrup only dispensed.

A. Improper water flow to

A. Check for water flow to dispenser

No water, but CO

2

gas

dispenser.

(see Section 8.2).

dispensed with syrup.

B. Carbonator pump motor has

B. Reset by turning the unit OFF and

timed out.

then ON, by using the ON/OFF

switch on top of the unit, or

unplugging unit momentarily.

C. Blown fuse on circuit board.

C. Check Fuse F1 on circuit board.

D. Liquid level probe not

D. Check connections of liquid level

connected properly to PCB.

probe to PCB assembly.

E. Faulty PCB assembly.

E. Replace PCB assembly.

F. Faulty liquid level probe.

F. Replace liquid level probe.

G. Water bath frozen.

G. Thaw water bath and repair faulty

component.  (See refrigeration

related symptoms.)

H. Water line frozen.

H. See Section 8.11.

8.8

Dispenser does not

A. Membrane switch

A. Reconfigure membrane switch

dispense proper syrup

configuration is wrong.

following steps in Section 5.

and/or water from

B. Tubing is improperly routed

B. Move water and syrup fittings to

proper nozzle.

from module to nozzles.

proper nozzle.

8.9

Excessive foaming.

A. Incoming water or syrup

A. Correct prior to dispenser.

temperature too high.

Consider larger dispenser or

pre-cooler.

B. CO

2

pressure too high.

B. Adjust CO

2

pressure downward,

but not less than 70 PSI.

C. Air in BIB lines.

C. Bleed air from BIB lines.

D. Poor quality ice.

D. Check quality of ice used in drink.

E. High beverage temperature.

E. Check refrigeration system.

8.10

Water continually

A. Loose water connection(s).

A. Tighten water connection(s).

overflows from water

B. Flare seal washer leaks.

B. Replace flare seal washer.

bath into drip tray.

C. Faulty water coil.

C. Replace water coil.

8.11

Compressor starts and

A. PCB malfunctioning or faulty

A. Disconnect ice bank probe from

continues to run until

ice bank probe.

PCB.

freeze up and will not

1. If compressor continues to run,

cut off.

check relay in control box on

refrigeration deck.  If stuck

closed, replace relay.  If not

stuck, replace circuit board.

2. If compressor stops, replace

ice bank probe.

B. Ice bank probe positioned

B. Check positioning of ice bank

improperly.

probe, and replace if needed.

C. Ice bank probe shorted to ground. C. Replace ice bank probe.

NOTE:

First check to ensure that the three (3) minute carbonator timer has not timed out.  Turn unit

OFF and then ON.  If the pump shuts off in less than 30 seconds, the dispenser is not frozen.

8.12

Warm drinks.

A. Restricted airflow.

A. Check clearance around sides,

top, and inlet of unit.  Remove

objects blocking airflow through

grill.

B. Dispenser connected to hot

B. Switch to cold water supply.

water supply.

C. Refrigeration system not

C. See Sections 8.13 - 8.17.

running.

D. Refrigerant leak.

D. Repair and recharge.

E. Condenser fan motor not

E. Replace condenser fan motor.

working.

F. Dirty condenser.

F. Clean condenser.

G. Dispenser capacity exceeded. G. Add pre-cooler or replace with

larger dispenser.

Summary of Contents for 600 LFCV Series

































Reviews: