Lami Corporation Lotus-14LK-H Instruction Manual Download | Manualshive

Page: 11 / 24

background image

10

『CURRENT TEMPERATURE』 button

Temperature display switch button

『MEMORY』 button

When  【CURRENT  TEMPERATURE】  button  is  pressed,
current  surface  temperature  of  the  roller  is  displayed.
【MEASURE】  is  displayed  while  the  button  is  being
pressed.

【Current Temperature】
button is pressed in
HOT setting

【℃/℉】

button

is

pressed once in HOT
setting

Whenever 【℃/℉】 button is pushed, it is switched
between Celsius display (℃) and Fahrenheit display (℉).
This document explains temperatures in Celsius.

When  【MEMORY】  button  is  pressed,  pre-registered
temperature  and  speed  settings  are  set.  There  are  3
patterns of setting, which can be switched by pressing the
button.
When  【MEMORY】  button  is  pressed,  【MEMORY】  is
displayed on LCD with  【

1

】, 【

2

】 or 【

3

】 to the right.

Registered values cannot be changed.

Power is turned ON and
【MEMORY】

button

is

pressed once to set to
setting temperature

190

℃

/ speed 3

180

℃

/ speed 3

170

℃

/ speed 5

180

356

«
...
9
10
11
12
13
...
»

Summary of Contents for Lotus-14LK-H

























Reviews:

No comments

Related manuals for Lotus-14LK-H

Brand: SEAL Pages: 36

Brand: Q-Connect Pages: 19

Brand: Peach Pages: 17

Brand: ibico Pages: 7

Brand: GBC Pages: 22

Brand: Olympia Pages: 86

Falcon 60+ (-1)

Brand: GBC Pages: 27

Brand: Matrix Pages: 5

Brand: Matrix Pages: 10

Brand: Matrix Pages: 18

Brand: Matrix Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands