Lami Corporation Lotus-14LK-H Instruction Manual Download Page 21

Page: 21 / 24

Be careful about the following matters when transporting or storing this product.

Movement and storage of laminator

Precautions for movement

Precautions for storage

①

Confirm that roller temperature is low and power is turned off.

②

Lift the lever and turn the power OFF.

③

Remove power plug from the outlet.

④

Hold the main body with both hands during transportation.

※ Bottom of the main body can be hot immediately after processing.

Check temperature before moving.

⑤

Refer to P3 for installation places and install the product in a safe place.

①

Confirm that roller temperature is low and power is turned off.

②

Lift the lever and turn the power OFF.

③

Remove power plug from the outlet.

④

After body temperature reaches room temperature, place in an exclusive box for storage.
※ If there is no box, cover the main body with a cover to prevent dusts on the rollers. Here,

cover must be placed after temperature of the body reaches room temperature.

Summary of Contents for Lotus-14LK-H

























Search results

Summary of Contents for Lotus-14LK-H

Reviews:

Related manuals for Lotus-14LK-H

Brands by name

Popular brands

Lami Corporation Lotus-14LK-H, Instruction Manual

Search results

Summary of Contents for Lotus-14LK-H

Reviews:

Related manuals for Lotus-14LK-H

Brands by name

Popular brands