Lami Corporation Lotus-14LK-H Instruction Manual Download | Manualshive

Page: 19 / 24

background image

18

When completing laminate processing, the laminate roller can be broken or damaged by turning

power off immediately. Use 【COLD】 function to decrease temperature of the laminate roller and

finish the work before turning power off.

When completing laminate processing

The machine can be immediately turned off by lifting the lever without using COLD function, but
frequent use of this can shorten lifetime of rollers.

COLD function

When 【COLD】 button on the operation panel is pushed, setting temperature is set to 0℃.

If the roller continues to rotate but surface temperature falls below 120℃, cooling fan will automatically

stop. Then lift the lever to turn power off.

Power OFF

Lift the lever.

Push

【COLD】

button

in

HOT

setting

Temperature: 0℃
Speed: 1.

FAN will stop when
surface

temperature

falls below 120℃.

«
...
17
18
19
20
21
...
»

Summary of Contents for Lotus-14LK-H

























Reviews:

No comments

Related manuals for Lotus-14LK-H

Brand: Deli Pages: 15

Brand: Lami Corporation Pages: 17

Brand: Hama Pages: 166

Brand: Fellowes Pages: 11

Brand: Argo Pages: 8

Brand: Swingline Pages: 24

Brand: Tamerica Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands