Laird ConnexLink CL2510 User Manual Download | Manualshive

Page: 27 / 28

background image

24

CL2510

RF Transceiver

global

solutions:

local

support

TM

Americas: +1.800.492.2320
Europe: +44.1628.858.940
Asia: +852.2268.6567

[email protected]

www.lairdtech.com/wireless

CL2510

COmPLIANCE

SECTION

CE APPROVED ANTENNA LIST

Part Numbers CL2510-050-232 and CL2510-050-422 are approved for use in CE Markets with antennas having
a maximum gain of 2.5dBi. Antennas having a gain greater than the maximum allowed are strictly prohibited
for use with this device. The required antenna impedance is 50 Ohms.

CE TESTED ANTENNA LIST*

Laird Technologies Part Number

Manufacturer Part Number Manufacturer

Type

Gain (dBi)

0600-00014

S181AH-2450S

Nearson

Dipole

2 dBi

ANT-DB1-RMS-RPS7

Antenna Factor Monopole 3 dBi

(The OEM is free to choose another vendor’s antenna of equal or lesser gain as an antenna appearing in the
table and still maintain compliance. Antennas listed in this table have been tested with the LT2510.

«
...
25
26
27
28
»

Summary of Contents for ConnexLink CL2510





























Reviews:

No comments

Related manuals for ConnexLink CL2510

Brand: HAMTRONICS Pages: 11

Brand: Nautel Pages: 224

Brand: Icom Pages: 64

Brand: Icom Pages: 132

Brand: Icom Pages: 40

Brand: Icom Pages: 27

DP harp EJX Series

Brand: YOKOGAWA Pages: 63

Brand: Yaesu Pages: 165

Brand: Radio Shack Pages: 11

Brand: Sennheiser Pages: 25

Brand: Ocean Signal Pages: 28

Brand: Yanglousi Technology Pages: 3

Brand: BNF Pages: 45

Brand: HiTV Pages: 28

Brand: Narco Avionics Pages: 16

Brand: Igema Pages: 24

EXTA LIFE ROM-22

Brand: Zamel Pages: 5

Brand: Brite View Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands