Laird ConnexLink CL2510 User Manual Download

Page: 14 / 28

www.lairdtech.com

Laird Technologies

CL2510

RF Transceiver

The software CD included with your programming kit provides a utility for changing the settings on each unit.
The software is compatible with Microsoft

Windows 95, 98, 2000, Me, NT and XP. Windows 7 and Windows

Vista are supported on a limited basis.

INSTALLATION

Locate the OEM software folder on the Laird Technologies Tools & Literature CD and install the

CL2510 Configuration Software. To install the software, run Setup.exe and follow the installation

prompts. During the installation, the software will prompt the user to install the Laird Technologies

USB Driver. It is recommended that the user installs the driver at the same time as the software. The first

time the software is run, the following message will be displayed:

Click “OK.” The software will attempt to open COM1 of the PC. If there is a conflict or the port does not

exist, the software will show the port as unavailable. This error will be displayed when one of the following
conditions exists:

• There is other software running that has control over the COM1 port. Locate this software and shut it

down while running “Laird OEM.exe” software.

• The PC either does not have a COM1 port or the port has been disabled.

CL2510
CONFIgURATION
UTILITY SOFTWARE

Summary of Contents for ConnexLink CL2510





























Search results

Summary of Contents for ConnexLink CL2510

Reviews:

Related manuals for ConnexLink CL2510

Brands by name

Popular brands

Laird ConnexLink CL2510, User Manual

Search results

Summary of Contents for ConnexLink CL2510

Reviews:

Related manuals for ConnexLink CL2510

Brands by name

Popular brands