LAI Games FireFighter Operator'S Manual Download Page 9

Page: 9 / 58

Operator's Manual

–

FireFighter

LAI GAMES

Page 4

MACHINE INSTALLATION and INSPECTION

When installing and inspecting

“Fire Fighter”

, be very careful of the following points

and pay attention to ensure that the players can enjoy the game safely.



Be sure to turn the power

OFF

before working on the machine.



Make sure the power cord is not exposed on the surface (floor, ground, etc.) where
people walk through.



Check that the rubber glide feet levelers are set evenly on the floor so that the game
cabinet is unable to roll and is stable.



Always make complete connections for the integrated circuit (IC) logic PC Boards
and other connectors. Insufficient insertion can damage the electrical components.



Only qualified personnel should inspect or test the integrated circuit (IC) logic PC
Boards.



If any integrated circuit (IC) logic PC Boards should need servicing. Please contact
the nearest

LAI GAMES

distributor.

(Refer to the back page of this manual)

* CAUTION! *

Before

switching the machine on be sure to check that it has been set on the

correct voltage for your area!

Refer

to the mains voltage adjustment section of this manual on page 37.

Machines are normally shipped on 220V AC unless otherwise specified.

* WARNING! *

Always

Turn

OFF

mains power before removing safety covers and refit all safety

covers when work is completed.

* CAUTION! *

Water needs to be added to the game

BEFORE

running the pumps.

Prolonged dry running of the pumps can shorten their life.

See page 6 on how to fill and setup the water system

Summary of Contents for FireFighter



























































Search results

Summary of Contents for FireFighter

Reviews:

Related manuals for FireFighter

Brands by name

Popular brands

LAI Games FireFighter, Operator'S Manual

Search results

Summary of Contents for FireFighter

Reviews:

Related manuals for FireFighter

Brands by name

Popular brands