background image

Mini-Therm JV

Page 5

Vent Damper (JVS only):

1.  Mini-Therm JVS boilers have built-in draft 

diverter for natural draft operation.

2.  Find the vent damper box which is located in the 

boiler package.

3.  Install the vent damper directly to the top of the 

draft diverter outlet with the damper operator 

facing to the front of the boiler, and with the flow 

direction arrow pointing upward. Use the vent 

damper wire harness provided with the boiler 

to connect the vent damper to the boiler. The 

bracket end of the harness should be connected to 

the vent damper actuator.

4.  For Model JVS only: Install the metal plug 

provided with the vent damper onto the damper 

plate hole. 

5.  Do not modify the automatic vent damper device. 

It is very important that no other vents are closed. 

Provide at least six inches clearance between 

the automatic vent damper and combustible 

construction, and be sure to allow access for 

servicing the damper.

Temperature/Pressure Gauge: 

Install the temp/

pressure gauge provided in the parts box.

2B. Boiler Placement

1.     The boiler must be placed to provide clearances 

on all sides for maintenance and inspection. There 

must also be minimum distances maintained from 

combustible surfaces. Avoid locations which can 

be damaged by water or moisture.

2.     A minimum of 15" (381mm) access must be 

available in front of the boiler for burner tray 

removal. Consult local codes for clearances to hot 

water pipes and accessories.

3.     If the boiler is to be installed in a garage, all 

burners and burner ignition devices must have 

a minimum 18" (457mm) clearance  

above the floor.

4.     Boilers can be installed in a closet as long as 

the minimum clearances shown in 

Table 2

 are 

observed. Special attention should be paid to 

clearances between the front of the boiler and the 

closet door when it is closed 

(see Figure 1)

.  

2C. Flooring

JVS model boilers can only be installed on  

noncombustible flooring.  

 

JVH model boilers are designed and certified for 

installation on a combustible floor.

All boilers must be installed on a level floor and 

must NEVER be installed on carpeting. 

NEVER store objects on or around the boiler.  

 

  

Noncombustible flooring

 is defined as flooring 

material and surface finish not capable of being 

ignited and burning and with no combustible materials 

against the underside. Acceptable materials are those 

consisting entirely of a combination of steel, iron, 

brick, tile, concrete, slate, glass or plaster. 

The JVS model boilers can be installed on a 

combustible floor if a noncombustible base 

assembly, available from Laars, is used.

 See the JVS 

Parts List at the back of this manual for the appropriate 

Noncombustible Base Kit part number. 

  

 

Figure 4. Typical Combustible Floor Installation.

As an alternative to the Laars Noncombustible Base 

Kit, in the United States the National Fuel Gas 

Code allows a heater to be placed on a combustible 

surface when there is a platform under the heater 

made of hollow masonry no less than 4 inches (102 

millimeters [mm]) thick, covered with sheet metal at 

least 24 gauge thick and extending beyond the full 

 WARNING

This boiler is intended for indoor installation only.

Do not install this boiler in a location subject to 

negative pressure, or improper operation will occur.

 

 

 

Avertissement

Cette chaudière est destiné pour une installation 

intérieure uniquement. Ne pas installer cette 

chaudière dans un endroit soumis à pression 

négative, ou fonctionnement incorrect se produira

 

 

Caution

Do not force motor operation when operator is 

fastened to the damper by moving the damper 

blade, turning the shaft or by turning the position 

indicator.

 

 

Attention

Ne pas tourner le registre manuellement avec 

ou sans courant électrique ou le moteur sera 

endommagé.

Summary of Contents for Mini-Therm JVH







































Reviews: