MAINTENANCE
1.Check the speed sensor if it is damaged or well fixed; the speed sensor has to be fixed where it close to the magnet within 2-3mm.
2.Check the signal cable of speed sensor if it is well connected to the controller. To solve the problem, please reconnect the signal
cable to the controller.
3.Please contact your local distributor for technical service.
1.Check the EEPROM if it is well fixed. To solve the problem, please reconnect the EEPROM IC.
2.Check the EEPROM’s pin if it is bent or well connected. To solve the problem, please reconnect the EEPROM IC.
3.Check the IC series number if it is correct. To solve the problem, please replace the EEPROM IC.
4.Please contact your local distributor for technical service.
1.Reconnect the black cable and red cable of the incline motor. To solve the problem, please contrary reconnect the cable.
2.Reconnect the signal cable of incline motor. To solve the problem, please contrary reconnect the cable or replace the
incline motor.
3.Please contact your local distributor for technical service.
1.Check the VR of incline motor if it is well fixed. To solve the problem, please replace the incline motor.
2.Unable to read the electric potential variation of incline motor. To solve the problem, please replace the incline motor.
3.Please contact your local distributor for technical service.
1.Upper control cable and lower control cable are not well connected. To solve the problem, please check the wiring circuit.
2.Please contact your local distributor for technical service.
The console is erratic or not lighting up:
Check to make sure that the treadmill is properly plugged in, turn the power switch off and back on again and make sure the safety
Check to make sure that the treadmill is properly plugged in, turn the power switch off and back on again and make sure the saf
Check to make sure that the treadmill is properly plugged in, turn the power switch off and back on again and make sure the saf
key is in place. If the problem persists contact your local distributor for technical service.
The belt does not stay in the center of the treadmill when in use:
First check to make sure that the treadmill is level, then refer to the instructions in this manual on how to tension and adjust the belt.
The treadmill motor seems strained:
The lubricating silicone that is applied to the deck and belt is wearing down and the belt needs to be lubricated with silicone spray.
The treadmill belt slips during use:
The belt may need to be tensioned after a period of use. Refer to the Belt Tensioning and Adjustment Section of this manual.
Heart Rate is erratic or not picking up(Only with HRC program):
Make sure your hands are moist (Aloe Vera helps). Make sure all connectors at the back of the console are properly connected and
no wires are damaged. If wearing a chest strap make sure the batteries are good and that the electrodes are moist and position
properly on your chest.
N/A
E1
Trouble shooting
E2
E6
E7
E9
N/A
N/A
N/A
N/A
Error
Code
The electronics are continuously running self-tests. If it finds any irregularities, the electronics console will display an error code and
stop normal operations for your safety.
Error codes description : E1 - Speed error E2 - Memory readout error E4 - Heart rate is not read from the heart rate sensors
E6 - Incline error E7 - Incline error E9 - Connection timed out
Raising/Lowering (Soft drop function)
Horizontal adjustment
Trouble shooting with error codes
Raising:
After the workout session, you
can raise the treadmill to the
upright position. Lift up the rear
end of the treadmill until the
upper and lower strut tube lock
(click) into position.
Lowering:
You can release the treadmill
from the upright position.
1. Push the frame by hand.
2. Push (click) upper and lower
strut tube with your foot.
3. Lower the treadmill by hand
and it will drop automatically
without any support.
To ensure the treadmill is level, located under the front of the base
frame there are two level adjusting screws.
1. Lift the machine on one side and then turn the screw under the front
of the base frame.
2. Turn the screw clockwise to adjust up.
3. Turn the screw counter clockwise to adjust down.
11