L-Acoustics K3i Owner'S Manual Download Page 34

Page: 34 / 85

Loudspeaker congurations

Use [xxxx_xx_C] or [xxxx_xx_Cx] on a reversed subwoofer in a cardioid conguration

The cardioid conguration consists in reversing 1 element in an array of 4 subwoofers.
Refer to the subwoofer owner's manual and to the

Cardioid congurations

technical bulletin.

Delay values

Do not forget to add the pre-alignment and geometric delays depending on the conguration.

Pre-alignment delays

K3 + KS28

presets

pre-alignment delay values and polarity settings

[K3] + [KS28_60]

K3 = 0.5 ms

KS28 = 0 ms

[K3] + [KS28_60_C]

K3 = 6 ms

KS28 = 0 ms

[K3] + [KS28_60_Cx]

K3 = 4 ms

KS28 = 0 ms

K3 + KS21

presets

pre-alignment delay values and polarity settings

[K3] + [KS21_60]

K3 = 0 ms

KS21 = 0 ms

[K3] + [KS21_60_C]

K3 = 5.5 ms

KS21 = 0 ms

[K3] + [KS21_60_Cx]

K3 = 5 ms

KS21 = 0 ms

K3i owner's manual (EN) version 1.0

Summary of Contents for K3i






















































































Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands

L-Acoustics K3i, Owner'S Manual

Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands