L-Acoustics K3i Owner'S Manual Download Page 64

Page: 64 / 85

Connection to LA amplied controllers

Cabling

Accessory

connector sealing plate (provided)

Screws and fasteners

4 x M5x16 screws (provided)

Tools

torque screwdriver
T25 Torx bit
small tool or at screwdriver (3 mm or less)

Min number of operators

Assembly

Prerequisite

The cable glands on the connector sealing plates are compatible with cables up to 4 × 4 mm

gauge.

Refer to:

•

APPENDIX A: Recommendation for speaker cables

(p.83)

•

Cabling schemes

(p.63)

About this task

The connector sealing plates have two cable glands: one for the input cable and one for the cable connecting to the next

enclosure in parallel. The second cable gland is equipped with a protective plug.
This procedure describes how to connect the input cable to the enclosure. If the enclosure must be connected in parallel,

remove the protective plug from the second cable gland and proceed identically for both cables.

Procedure

On the connector sealing plate, remove the sealing nut from the cable gland.

K3i owner's manual (EN) version 1.0

Summary of Contents for K3i






















































































Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands

L-Acoustics K3i, Owner'S Manual

Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands