L-Acoustics K3i Owner'S Manual Download Page 39

Page: 39 / 85

Rigging procedures

Tightening screws

Driving screws

Do not fully tighten the screws unless otherwise instructed.
Follow the indicated torque when tightening a screw.

When securing a rigging plate to an enclosure, secure the top and middle screws on both sides. Secure the bottom

screws only when instructed to.

Apply a torque of 7 N.m.

Stacking enclosures

Fastening brackets

Always secure a stacked array to the ground using K3i-TILTBRACKET to ensure the stability of the array.

When stacking two enclosures, the top enclosure must be slightly lifted to align the inserts with the rigging plate holes.

Use an accessory like a wedge or a lever to adjust the height of the enclosure. Be careful not to scratch the paint.

Tools

Before rigging this product, make sure all the tools listed are available. References are given for FACOM

products in this

table. Other manufacturers can be used.

name

reference

distributor

Set of 6-point 1/4" sockets

RL.NANO1 / R.360NANO

FACOM

electric screwdriver with torque

selector

K3i owner's manual (EN) version 1.0

Summary of Contents for K3i






















































































Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands

L-Acoustics K3i, Owner'S Manual

Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands