L-Acoustics K3i Owner'S Manual Download Page 23

Page: 23 / 85

Rigging system description

With K3i-RIGBAR as the main lifting accessory, K3i-ENDLINK is required on the top enclosure.

Secure K3i-RIGBAR at the front for a positive initial site angle.

T40

7 N.m

With K3i-RIGBAR as the main lifting accessory, CLAMP250 can be used to hang an array from a truss. If a pullback is

implemented, CLAMP250 cannot be used on the bottom K3i-RIGBAR. Refer to the

CLAMP250 owner's manual

for

more information.

Maximum limit with CLAMP250

CLAMP250 has a WLL (Working Load Limit) of 250 kg / 550 lb. It can support an array of up to 6 K3i. For an

hybrid array, check the total weight of the array in Soundvision.

When using K3i-RIGBAR as the main lifting accessory, always implement a secondary safety using available

holes.

pickup point

safety points

pickup points

safety point

K3i owner's manual (EN) version 1.0

Summary of Contents for K3i






















































































Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands

L-Acoustics K3i, Owner'S Manual

Search results

Summary of Contents for K3i

Reviews:

Related manuals for K3i

Brands by name

Popular brands