Kyocera ECOSYS P7035cdn Service Manual Download Page 133 | Manualshive

Page: 133 / 178

background image

2PR-1

1-6-3

10. Turn printer power off.
11. Remove the USB memory from USB mem-

ory slot.

12. Turn printer power on.
13. Print the status page to check that the firm-

ware version has been updated (See page
P.1-3-2).

Figure 1-6-4

Safe-UPDATE

If the device is accidentally switched off or the USB memory is disconnected and upgrading is incomplete, perform the fol-
lowing.
If the power is accidentally switched off, turn the power on without removing the USB memory and perform the above
steps 6 through 13.
If the USB memory is disconnected, reinsert it, then turn the power on and perform the above steps 6 through 13.
In any case, complete the steps to the end.

USB memory

USB memory slot

«
...
131
132
133
134
135
...
»

Summary of Contents for ECOSYS P7035cdn



















































































































































































Reviews:

No comments

Related manuals for ECOSYS P7035cdn

Brand: Canon Pages: 11

Brand: Canon Pages: 2

Brand: Canon Pages: 12

PIXMA Pro9000 Mark II Series

Brand: Canon Pages: 4

DocuPrint C525 A

Brand: Xerox Pages: 49

DocuPrint C2100

Brand: Xerox Pages: 206

Brand: Xerox Pages: 116

Brand: Xerox Pages: 358

Brand: Xerox Pages: 344

Brand: Xerox Pages: 59

Brand: Xerox Pages: 2

Brand: Xerox Pages: 10

Brand: Xerox Pages: 51

Brand: Xerox Pages: 110

7300DX - Phaser Color Laser Printer

Brand: Xerox Pages: 8

Brand: Xerox Pages: 220

Brand: Xerox Pages: 28

8400B - Phaser Color Solid Ink Printer

Brand: Xerox Pages: 203

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands