Kval 990-HQ Service Manual Download Page 103

Page: 103 / 112

With the power off, check for motor overloads by pressing each reset button (usu-

ally at the bottom of the panel) in SEQUENCE. If one is tripped there will be a
slight resistance to touch and a “click” sound as it is reset.

Trip Indicator

Press Reset

Thermal Overload Relay

Test

Troubleshooting Electrical Problems

4-22

990-HQ Service Manual

Check for Tripped Circuits

Remove lock and tag outs on the main power sources.

Manually close disconnect sensors and energize the control circuit or transformer

with its respective sensor. Check the Status Light Panel,. If all lights are observed,
there are no overloads or emergency stops tripped.

Note:

Most electrical problems are related to mechanical malfunction (e.g., stuck

motors, jammed chain, blocked photo sensors etc.)

Note:

If a solenoid valve is suspected, and not cleared in the air checks section, it can

be electrically jumped to check operation.

Summary of Contents for 990-HQ

















































































































Search results

Summary of Contents for 990-HQ

Reviews:

Related manuals for 990-HQ

Brands by name

Popular brands

Kval 990-HQ, Service Manual

Search results

Summary of Contents for 990-HQ

Reviews:

Related manuals for 990-HQ

Brands by name

Popular brands