manualshive.com logo in svg

Kusam-meco KM-CAL-907, User Manual

Share
Download
Kusam-meco KM-CAL-907 User Manual Download Page 59

 

59

14 How to use the charger 

Warning 

z

  The charger could be used only to specified product. 

z

  Make sure the voltage of the AC power is same with the given voltage of the charger before connecting 

them. 

z

  Do not shut circuit the output plug of the charger. 

z

  Do not charge non-Ni-Cd, non-Ni-MH battery or wasted battery. 

Step 1:

Turn off the calibrator. 

Step 2:

Connect the plug into the charging jack of the terminal.

 

Step 3

:Plug the charger into the AC power. 

Note: 

In normal charging function, the indicating light of the charger lights on. 
When finished, the charging function stops automatically, and the indicating light becomes dark. 
Blinking of the indicating light means the charger is not connected or no battery is inside. 

Note: 

Do not use the calibrator when it undergoes charging, otherwise, the charging will be prolonged. 
 
 
 

Summary of Contents for KM-CAL-907













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands