manualshive.com logo in svg

Kusam-meco KM-CAL-907, User Manual

Share
Download
Kusam-meco KM-CAL-907 User Manual Download Page 56

 

56

 
12.2 Adjusting Current Source 

Step 1: 

Using 

〔

mA

〕

key, select DC current function.

 

Connect the lead cables for measurement to the standard 
digital meter as shown in Figure 19. 

Step 3:

 The LCD shows “CA-0” or “CA-F” symbol on the 

associate districts part and the calibrator is ready                    Figure 19 Adjusting current source   
for the zero-point or F-point adjustment of source functions. The LCD shows the highest five digits and its unit 
in the main districts part and the lowest digit of the           
calibrated sourced value in the right of the assistance districts

 

part respectively. 

Step 3: 

Read the calibrator output on the calibration standard. Then, using the pair of

〔

S

〕

/

〔

T

〕

keys, adjust 

the reading so that it matches the measured CAL adjustment setpoint. In the CAL mode, the right pair of

〔

S

〕

/

〔

T

〕

keys are used to increase or decrease the least-significant digit, (the digit in the right of LCD part).   

Step 4: 

Press the

〔

25/100%

〕

key to save the CAL adjustment reading. 

 

（

accuracy

0. 005％）

digital meter
(KEITHLEY2000

)

Lo

Hi

100

Ω

 

standard resistance

Summary of Contents for KM-CAL-907













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands