KUHN FC243RGII Operator'S Manual Download Page 95

Page: 95 / 112

11. - Troubleshooting guide

FC243RGII

KN041BGB A

Mower conditioner

11. Troubleshooting guide



Problem



Cause



Remedy

Uneven stubble.

Dull or broken knives.

Replace knives.

Knives not installed
correctly.

Make sure the arrow on
the knife upper face is
pointing in the disc's
direction of rotation.

Too low PTO speed
(rotational frequency).

Increase speed to
540 min

-1

Soil build up in front of the
cutterbar.

Too much cutterbar down
pressure.

Increase accumulator
pressure.

Very wet working
conditions.

Adjust main frame height
with regards to the ground.

Bad ground contour
adaptation.

Incorrect main frame
setting.

Adjust main frame height
with regards to the ground.

Excessive ground speed.

Reduce ground speed.

Insufficient ground
pressure.

Reduce accumulator
pressure.

Obstruction of conditioning
rotor.

Insufficient rotor speed
(rotational frequency).

Check that the rotor drive
belts are correctly
tensioned.

Too low PTO speed
(rotational frequency).

Increase speed to
540 min

-1

Swath shields too closed.

Open swath shields.

Badly shaped windrows.

Belts slip.

Retension belts.

Too low PTO speed
(rotational frequency).

Increase speed to
540 min

-1

Incorrectly adjusted swath
shields.

Adjust both swath shields.

Insufficient cutterbar
ground clearance in
"headland turn" position.

Incorrect tractor lift linkage
setting.

See machine attachment.

Too long levelling rod
adjustment on tractor 3-
point lift.

Shorten levelling rods on
tractor 3-point lift.

Summary of Contents for FC243RGII

















































































































Search results

Summary of Contents for FC243RGII

Reviews:

Related manuals for FC243RGII

Brands by name

Popular brands

KUHN FC243RGII, Operator'S Manual

Search results

Summary of Contents for FC243RGII

Reviews:

Related manuals for FC243RGII

Brands by name

Popular brands