manualshive.com logo in svg

Kubota RT120Q, Operator'S Manual, Page: 166 / 219

Share
Download
Kubota RT120Q Operator'S Manual Download Page 166

RT120Q Operator’s Manual

Service - 165

10 Hour

Lube Trencher Auger Shaft

Lube four auger shaft zerks (two on each side) 
every 10 hours with EPG.

Check Trencher Auger Bolts

Check trencher auger bolts every 10 hours. For 
optimal spoils delivery, adjust augers to match 
terrain and digging depth.

Check Digging Chain Teeth and Bits

Check teeth (1) for wear every 10 hours. Replace 

worn teeth, using Ditch Witch

®

 replacement parts 

and maintaining original tooth pattern.

For more efficient digging, contact your Ditch 
Witch dealer for information about the tooth 
pattern best suited to your jobsite.

If using rock chain bits, check that bits rotate 
freely. Clean chain and check bits after each use. 
Replace bit when carbide cap or insert is worn or 
adapter can be damaged.

Check chain every 10 hours. Replace worn or 
broken chains. If sidebars (2) are bent or loose on chain pins (3), chain spacers should be used to join 
sidebars.

Summary of Contents for RT120Q




























































































































































































































Reviews:

No comments