Kubota RT120Q Operator'S Manual Download Page 114

Page: 114 / 219

RT120Q Operator’s Manual

Plow - 113

Finish Job

When installation is complete, move plow swing out of float.

Move ground drive hand control to neutral.

With vibrator running, raise plow to ground level while reducing vibrator speed.

Move attachment speed/direction control to neutral.

Swivel seat to the drive position.

Tilt steering wheel column down.

Set parking brake and verify parking brake indicator is on.

Lower backfill blade, if equipped.

Turn ignition switch to STOP and remove product from plow.

10. Turn ignition switch to ON.

11. Swing plow to center position and engage swing lock and stow lock.

12. Release parking brake.

13. Raise backfill blade, if equipped.

14. Disengage axle lock. After disengaging axle lock, drive tractor in reverse 6’ (2 m) to fully disengage.

15. Drive a short distance away from work site. See “Drive” on page 85.

16. Shut down tractor. See page 87 for proper shutdown procedures.

NOTICE:

Do not operate vibrator when plow is out of the ground.

Summary of Contents for RT120Q




























































































































































































































Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands

Kubota RT120Q, Operator'S Manual

Search results

Summary of Contents for RT120Q

Reviews:

Related manuals for RT120Q

Brands by name

Popular brands