KStar HIP3300E Operation Manual Download

Page: 76 / 78

Definition of port :

Connection between the Device’s CAN coverter port and UPS CAN port.

BMS

UPS

（

RJ45

）

Description

PIN 1

CAN_H

PIN 2

CAN_L

PIN 3/7

CAN_GND

Available function of CAN

◆

Communicate to BMS.

◆

Communicate to remote LCD.

Appendix 4 RS485 communication port definition

Definition of port :

Connection between the Device’s RS485 port and UPS RS485 port.

device(RJ45)

UPS(RJ45)

Description

Pin 1/5

485+ “A”

Pin 2/4

485 - “B”

Available function of RS485

◆

Monitor UPS power status.

◆

Monitor UPS alarm info.

◆

Monitor UPS running parameters.

◆

Timing off /on setting.

RS485 communication data format

Baud rate ---------- 9600bps
Byte length ---------- 8bit
End bit ---------- 1bit
Parity check ---------none

Appendix 5 BAT_T communication port definition

Definition of port :

Summary of Contents for HIP3300E















































































Search results

Summary of Contents for HIP3300E

Reviews:

Related manuals for HIP3300E

Brands by name

Popular brands

KStar HIP3300E, Operation Manual

Search results

Summary of Contents for HIP3300E

Reviews:

Related manuals for HIP3300E

Brands by name

Popular brands