KSB UPA Installation & Operating Manual Download Page 64

Page: 64 / 98

7 Servicing/Maintenance

64 of 98

UPA / UPA S

3400.86/17-EN

DANGER

Supply frequency inverter switched on or frequency inverter not discharged

Electric shock by electrical voltage at the motor lead ends and at the inverter
terminals and filter terminals!

▷

Observe the safety regulations which apply to work involving electrical hazards.
Verify that the equipment is de-energised.

WARNING

Persons could fall into unsecured wells/reservoirs/tanks

Risk of personal injury!

▷

During installation work, take suitable precautions to protect anyone from
falling into an open well/reservoir/tank.

▷

Suitably fence off the work area.

WARNING

Uncontrolled lifting of the pump (set) or drive

Risk of injury!

▷

Maintain adequate safety distance during lifting operations (load may swing
when being lifted).

WARNING

Pump set tilting

Risk of squashing hands and feet!

▷

Suspend or support the pump set.

Suitable lifting equipment for the total weight has been selected and is on hand.
(

Section 5.2.6, Page 30)

Suitable dismantling equipment, e.g. supporting clamps or mounting plate are
available.

1. Disconnect the pump set from the power supply and secure it against

unintentional start-up.

2. For removing the pump set refer to the assembly/dismantling instructions of the

corresponding riser.

WARNING

Placing down a pump set with pipe sections of extensive length

Impermissible bending of the pump set when setting it down!

▷

The length of the last pipe section flanged to the pump set must not exceed 2
metres.

3. Place the pump set in a horizontal position on a solid and level surface and

secure it against rolling off.

Summary of Contents for UPA



































































































Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands

KSB UPA, Installation & Operating Manual

Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands