KSB UPA Installation & Operating Manual Download Page 15

Page: 15 / 98

3 Transport/Storage/Disposal

15 of 98

UPA / UPA S

3400.86/17-EN

CAUTION

Excessive bending stress on the pump set

Damage to the pump set!

▷

Choose attachment points which prevent excessive bending stress on the pump
set.

Suitable lifting equipment for the total weight has been selected and is on hand.

1. Fasten to a suitable lifting accessory, e.g. mounting plate.

2. Attach the lifting equipment, pull the pump/motor/pump set upright, and

secure it against tipping over.

3.4 Storage/preservation

If commissioning is to take place some time after delivery, we recommend that the
following measures be taken:

WARNING

Pump set tilting or rolling off

Risk of personal injury!

▷

Always secure vertically positioned pump sets against tipping over.

▷

Always secure horizontally positioned pump sets against rolling off.

WARNING

Laying electric cables at temperatures below zero degrees

Damage to the electric cable!

▷

Observe the minimum permissible temperature at the cable surface of -25 °C for
moving cables.

▷

Observe the minimum permissible temperature at the cable surface of -40 °C for
stationary cables.

CAUTION

Ambient temperature below the specified minimum

Danger of frost!

▷

Never subject the pump set to ambient temperatures which are lower than
those permitted for the drinking water/antifreeze mixture provided.

CAUTION

Improper storage

Damage to the electric cables!

▷

Observe the minimum bending radius

of the electric cables.

▷

Only remove the protective caps from the electric cables at the time of
installation.

For temporary storage, store submersible borehole pumps as follows:

In the original packaging: in a

horizontal

position

Without packaging: in a

vertical

position with the motor below

In a dry environment

Protected against direct sunlight and heat

Observe the cable manufacturer's documentation, DIN VDE 0298-3 and/or the general arrangement drawing.

Summary of Contents for UPA



































































































Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands

KSB UPA, Installation & Operating Manual

Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands