KSB UPA Installation & Operating Manual Download Page 45 | Manualshive

Page: 45 / 98

background image

5 Installation at Site

45 of 98

UPA / UPA S

3400.86/17-EN

DANGER

Earth conductor not properly connected

Danger of death from electric shock!

▷

Never operate the motor without earth conductor.

▷

The earth conductor must be connected by a professional electrician only.

WARNING

Incorrect connection to the mains

Damage to the power supply network, short circuit!

▷

Observe the technical specifications of the local energy supply companies.

NOTE

Only

VDS-approved switchgear

shall be used for pump sets in sprinkler

installations.
Due to the special conditions of pumps in fire protection applications, switchgear
with overcurrent relay must not be used, for example.

1. Check the available mains voltage against the data on the name plate.

2. Select an appropriate start-up method and observe the respective requirements.

3. Check the starting method in the data sheet and select the corresponding circuit

diagram.

4. Connect the power cable including earth conductor.

5. Remove the safety notice from the motor lead ends and attach it near the actual

place of connection.

In the case of UMA-S 150, UMA-S 200 and UMA-S 250 submersible motors, the power
cable cores are connected together at the time of supply. Prior to disconnecting
them, make sure that the motor is not rotating (e.g. due to backflow in the pump
caused by a lack of or a defective check valve). Observe the safety regulations that
apply to work involving electrical hazards. Verify that the equipment is de-energised.

NOTE

Connect the shielded motor power cable with the exposed shield as short as
possible and the shield ends having contact over a large area. Interruptions of the
shield must be compliant with EMC

16)

. Observe the EMC instructions given by the

equipment manufacturers.

Single-phase (1~) motors with one power cable for DOL starting

For this motor type a starting device is required. The starting device is included in the
scope of supply.

1. Check the terminal assignment diagram. Wire the starting device in accordance

with the illustration and the manufacturer’s product literature.

16

Electromagnetic compatibility

«
...
43
44
45
46
47
...
»

Summary of Contents for UPA



































































































Reviews:

No comments

Related manuals for UPA

Brand: Samson Pages: 48

Brand: Mako Networks Pages: 15

Concord express

Brand: GE Pages: 3

Brand: Wavelink Pages: 69

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: YOKOGAWA Pages: 150

Brand: YOODA Pages: 3

Brand: YMGI Pages: 8

Cutler-Hammer LMR

Brand: Eaton Pages: 38

CentralControl CC41

Brand: Becker Pages: 48

Brand: GSK Pages: 32

Waukesha Cherry-Burrell D4 Series

Brand: SPX FLOW Pages: 34

Brand: Lauda Pages: 40

Brand: Cooper Pages: 4

Brand: Trenz Electronic Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands