KSB UPA Installation & Operating Manual Download Page 28 | Manualshive

Page: 28 / 98

background image

5 Installation at Site

28 of 98

UPA / UPA S

3400.86/17-EN

A1

A2

B

C

Fig. 6:

Checking the installation position

A1

Permissible up to
maximum 3°

Installing the pump set in a vertical position
(

Section 5.3, Page 34)

A2

Permissible up to
maximum 3°

Installing the pump set in a horizontal position
(

Section 5.4, Page 38)

B

Permissible installation position,

if

approved

in the order documentation

C

Not permitted

The pump set must not be installed in this
position.

5.2.3 Checking the motor fill

CAUTION

Unfilled or insufficiently filled motor

Damage to the motor winding!

▷

Never install and run the motor without sufficient motor fill.

▷

Observe the information sticker on the motors and top up the motor fill as
instructed.

CAUTION

Freezing of motor fill

Damage to the motor!

▷

Always protect motors filled with water against frost.

▷

Provide frost-proof storage.

Information sticker / motor fill

Submersible motors are filled with a liquid based on drinking water.
A distinction is made between filled and unfilled motors, marked by a colour-coded
information sticker attached to the motor.

Motors which are supplied filled with a mixture of drinking water / antifreeze agent
must not be filled with pure drinking water at a later stage without prior
consultation with the manufacturer.

Table 11:

Motor fill details

Motor type
series

Supplied
condition

Information sticker

Motor fill check required

See Section

DN 100

Filled

-

Not required

Section 7.4.1, Page 68)

UMA 150

Filled

-

Required if the motor has been
stored or out of service for more than
1 year

Section 7.4.2, Page 68)

«
...
26
27
28
29
30
...
»

Summary of Contents for UPA



































































































Reviews:

No comments

Related manuals for UPA

Brand: Datavideo Pages: 8

Brand: Gate Motors Pages: 6

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: Madison AV Pages: 2

SUPERSTAR E-3000/F2

Brand: praher Pages: 10

Brand: IDEC Pages: 97

Brand: IMG STAGELINE Pages: 14

Brand: VAT Pages: 77

Brand: DAY Pages: 23

Lift Inverter L1000V

Brand: YASKAWA Pages: 282

Brand: Bardiani Pages: 22

Brand: Radio Shack Pages: 29

Brand: TAC Pages: 76

Brand: FAAC Pages: 16

Brand: Mitsubishi Pages: 2

Brand: BLACKMER Pages: 8

Brand: D+H Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands