KSB UPA Installation & Operating Manual Download Page 12

Page: 12 / 98

3 Transport/Storage/Disposal

12 of 98

UPA / UPA S

3400.86/17-EN

3 Transport/Storage/Disposal

3.1 Checking the condition upon delivery

1. On transfer of goods, check each packaging unit for damage.

2. In the event of in-transit damage, assess the exact damage, document it and

notify KSB or the supplying dealer and the insurer about the damage in writing
immediately.

NOTE

The pump set/pump/motor is supplied by the manufacturer/supplier in packaging
which largely prevents sagging or other damage during transport and/or storage.

3.2 Transport

DANGER

Improper transport

Personal injury and damage to property!

▷

Do not use add-on parts, such as dosing equipment, pipelines and centring
devices for transport purposes.

WARNING

Improper transport

Risk of crushing hands and feet!

Damage to the pump set!

▷

Always transport the pump set in a horizontal position.

▷

Do not use power cables for transport.

▷

Gently place the pump set down on a suitable surface.

▷

Observe the centre of gravity of the pump set and the weights indicated.

WARNING

Pump set tilting or rolling off

Risk of personal injury!

▷

Always secure vertically positioned pump sets against tipping over.

▷

Always secure horizontally positioned pump sets against rolling off.

CAUTION

Ambient temperature below the specified minimum

Danger of frost!

▷

Never subject the pump set to ambient temperatures which are lower than
those permitted for the drinking water/antifreeze mixture provided.

NOTE

Take into account the unequal weight distribution between pump and motor.

Magnet rotor

Magnet rotors are always stored and transported in non-magnetic, latchable boxes,
which

are marked with special safety notices on the outside

. The distance from the

magnet rotor to the outside of the box must be equivalent to the safety distance of
0.3 m as a minimum.

Summary of Contents for UPA



































































































Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands

KSB UPA, Installation & Operating Manual

Search results

Summary of Contents for UPA

Reviews:

Related manuals for UPA

Brands by name

Popular brands