KSB Hya-Rain Installation & Operating Manual Download Page 53

Page: 53 / 64

10 Related Documents

53 of 64

Hya-Rain/Hya-Rain N

10 Related Documents

10.1 General assembly drawing with list of components

81-99

741.02

591

655

719.02

719.01

71-14

719.03

672

81-99.01
82-16

691

741.01
741.03

411.01 719.01

Fig. 46:

Sectional drawing

Table 20:

List of components

Part No.

Description

411.01

Profile seal for the pump control unit

591

Mains water storage tank

62-12

Level sensor for the rainwater storage tank

655

Pump, complete with set of sealing elements

672

Globe valve (vent valve)

691

Pressure gauge

71-14

Pipe with sealing element

719.01

Hose (inlet side)

719.02

Hose (discharge side)

719.03

Hose with clamp

741.01

Three-way valve with tank

741.02

Float valve, complete

741.03

Thee-way valve

81-9

Relay

81-99

Electrical part (complete)

81-99.01

Electrical part (printed circuit board for Hya-Rain N)

82-16

Control unit / control panel for Hya-Rain

82-16

Control unit / control panel for Hya-Rain N

99-9

Set of sealing elements

Pump components, see Multi Eco (5180.5) type series booklet.

Summary of Contents for Hya-Rain

































































Search results

Summary of Contents for Hya-Rain

Reviews:

Related manuals for Hya-Rain

Brands by name

Popular brands

KSB Hya-Rain, Installation & Operating Manual

Search results

Summary of Contents for Hya-Rain

Reviews:

Related manuals for Hya-Rain

Brands by name

Popular brands