KSB Hya-Rain Installation & Operating Manual Download Page 24

Page: 24 / 64

5 Installation at Site

24 of 64

Hya-Rain/Hya-Rain N

5.5.2 Connecting the level control system

5.5.2.1 Connecting the sensor

CAUTION

Liquids entering the terminal box

Damage to the sensors!

System defect!

▷

Mount the terminal box approx. 10 cm above the rainwater storage tank
overflow.

Overflow

min.

10 cm

SENSOR terminals

CABLE terminal

Data cable

Data cable connection
reverse polarity protected

SENSOR terminal

Connect sensor at terminal S.

The cables
must not be twisted.

To tighten the cable
the suspended sensor can end
just above the tank floor.

10 cm

PG2

PG3

PG1

Connect the cable
at terminal K.

100%
reference value
Mark the
sensors at
this point.

Fig. 11:

Connecting the sensor

1. Mount the terminal box supplied at least 10 cm above the overflow. Fasten it to

the rainwater storage tank wall or to a pipe.

The sensors hang down straight and can move freely.

2. Cut the sensors, so the weights hang approx. 10 cm above the floor of the

rainwater storage tank.

3. Strip the ends of the power cables. Connect the cables to terminals K and S.

4. Tighten the cable glands.

Summary of Contents for Hya-Rain

































































Search results

Summary of Contents for Hya-Rain

Reviews:

Related manuals for Hya-Rain

Brands by name

Popular brands

KSB Hya-Rain, Installation & Operating Manual

Search results

Summary of Contents for Hya-Rain

Reviews:

Related manuals for Hya-Rain

Brands by name

Popular brands