KSB HPK-L Installation & Operating Manual Download Page 32

Page: 32 / 74

5 Installation at Site

32 of 74

HPK-L

1136.8/15-EN

Fig. 18:

Pump set with shim

Shim

The coupling guard and its footboard, if any, have been removed.

1. Check the coupling alignment.

2. Loosen the hexagon head bolts at the motor.

3. Insert shims underneath the motor feet until the difference in shaft centreline

height has been compensated.

4. Re-tighten the hexagon head bolts.

5. Check proper functioning of coupling/shaft.

Check that coupling/shaft can easily be rotated by hand.

WARNING

Unprotected rotating coupling

Risk of injury by rotating shafts!

▷

Always operate the pump set with a coupling guard.
If the customer specifically requests not to include a coupling guard in KSB's
delivery, then the operator must supply one!

▷

Observe all relevant regulations for selecting a coupling guard.

DANGER

Risk of ignition by frictional sparks

Explosion hazard!!

▷

Choose a coupling guard material that is non-sparking in the event of
mechanical contact.

6. Fit the coupling guard and its footboard, if any.

7. Check the distance between coupling and coupling guard.

The coupling guard must not touch the coupling.

5.7 Electrical connection

DANGER

Electrical connection work by unqualified personnel

Risk of fatal injury due to electric shock!

▷

Always have the electrical connections installed by a trained and qualified
electrician.

▷

Observe regulations IEC 60364 and, for explosion-proof models, EN 60079.

Summary of Contents for HPK-L











































































Search results

Summary of Contents for HPK-L

Reviews:

Related manuals for HPK-L

Brands by name

Popular brands

KSB HPK-L, Installation & Operating Manual

Search results

Summary of Contents for HPK-L

Reviews:

Related manuals for HPK-L

Brands by name

Popular brands