KSB HPK-L Installation & Operating Manual Download Page 63 | Manualshive

Page: 63 / 74

background image

8 Trouble-shooting

63 of 74

HPK-L

1136.8/15-EN

8 Trouble-shooting

WARNING

Improper work to remedy faults

Risk of injury!

▷

For any work performed to remedy faults, observe the relevant information
given in this operating manual and/or in the product literature provided by the
accessories manufacturer.

If problems occur that are not described in the following table, consultation with the
KSB service is required.

A

Pump delivers insufficient flow rate

B

Motor is overloaded

C

Excessive discharge pressure

D

Increased bearing temperature

E

Leakage at the pump

F

Excessive leakage at the shaft seal

G

Vibrations during pump operation

H

Impermissible temperature increase in the pump

Table 23:

Trouble-shooting

A B C D E

F G H Possible cause

Remedy

12)

✘

-

-

-

-

-

-

- Pump delivers against an excessively

high pressure.

Re-adjust to duty point.
Check system for impurities.
Fit a larger impeller.

13)

Increase the speed (turbine, I.C. engine).

✘

-

-

-

-

-

✘ ✘

Pump or piping are not completely
vented or primed.

Vent and/or prime.

✘

-

-

-

-

-

-

- Supply line or impeller clogged

Remove deposits in the pump and/or piping.

✘

-

-

-

-

-

-

- Formation of air pockets in the piping

Alter piping layout.
Fit vent valve.

✘

-

-

-

-

-

✘ ✘

Suction lift is too high/
NPSH

available

(positive suction head) is too

low.

Check/alter fluid level.
Install pump at a lower level.
Fully open the shut-off element in the suction
line.
Change suction line, if the friction losses in the
suction line are too high.
Check any strainers installed/suction opening.
Observe permissible speed of pressure fall.

✘

-

-

-

-

-

-

- Air intake at the shaft seal

Clean barrier fluid duct, supply external barrier
fluid, if necessary, or increase barrier fluid
pressure.
Replace shaft seal.

✘

-

-

-

-

-

-

- Wrong direction of rotation

Check the electrical connection of the motor
and the control system, if any.

✘

-

-

-

-

-

-

- Speed is too low.

13)

- Operation with frequency inverter
- Operation without frequency inverter

- Increase voltage/frequency at the frequency
inverter in the permissible range.
- Check voltage.

✘

-

-

-

-

-

✘

- Impeller

Replace worn components by new ones.

12

Pump pressure must be released before attempting to remedy faults on parts which are subjected to pressure.

13

Contact KSB.

«
...
61
62
63
64
65
...
»

Summary of Contents for HPK-L











































































Reviews:

No comments

Related manuals for HPK-L

Brand: Water Factory Systems Pages: 15

Brand: A.O. Smith Pages: 64

Brand: A.O. Smith Pages: 4

Brand: A.O. Smith Pages: 4

Brand: A.O. Smith Pages: 4

120 through 250 Series

Brand: A.O. Smith Pages: 74

Brand: Davey Pages: 8

Brand: Davey Pages: 8

Brand: Davey Water Products Pages: 4

Brand: Ulvac Pages: 54

Brand: Austria Email Pages: 32

Brand: Gorenje Tiki Pages: 48

Brand: Dantherm Pages: 17

Brand: GEA Pages: 66

Brand: Daikin Pages: 36

Brand: samhydraulik Pages: 9

Brand: Trigano PISCINES Pages: 13

Brand: Homa Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands