KSB HPK-L Installation & Operating Manual Download Page 31

Page: 31 / 74

5 Installation at Site

31 of 74

HPK-L

1136.8/15-EN

5.6.1 Motors with adjusting screw

Fig. 17:

Motor with adjusting screw

Hexagon head bolt

Adjusting screw

Locknut

The coupling guard and its footboard, if any, have been removed.

1. Check the coupling alignment.

2. Unscrew the hexagon head bolts (1) at the motor and the locknuts (3) at the

baseplate.

3. Turn the adjusting screws (2) by hand or by means of an open-end wrench until

the coupling alignment is correct and all motor feet rest squarely on the
baseplate.

4. Re-tighten the hexagon head bolts (1) at the motor and the locknuts (3) at the

baseplate.

5. Check proper functioning of coupling/shaft.

Check that coupling/shaft can easily be rotated by hand.

WARNING

Unprotected rotating coupling

Risk of injury by rotating shafts!

▷

Always operate the pump set with a coupling guard.
If the customer specifically requests not to include a coupling guard in KSB's
delivery, then the operator must supply one!

▷

Observe all relevant regulations for selecting a coupling guard.

DANGER

Risk of ignition by frictional sparks

Explosion hazard!!

▷

Choose a coupling guard material that is non-sparking in the event of
mechanical contact.

6. Fit the coupling guard and its footboard, if any.

7. Check the distance between coupling and coupling guard.

The coupling guard must not touch the coupling.

5.6.2 Motors without adjusting screw

Any differences in the centreline heights of the pump and motor shafts are
compensated by means of shims.

Summary of Contents for HPK-L











































































Search results

Summary of Contents for HPK-L

Reviews:

Related manuals for HPK-L

Brands by name

Popular brands

KSB HPK-L, Installation & Operating Manual

Search results

Summary of Contents for HPK-L

Reviews:

Related manuals for HPK-L

Brands by name

Popular brands