manualshive.com logo in svg

Krone Swadro 810, Operating Instructions Manual, Page: 53 / 64

Share
Download
Krone Swadro 810 Operating Instructions Manual Download Page 53

IX - 1

Winter storage

9

Winter storage

•

Thoroughly clean the rotary swather before winter
storage. If a high-pressure cleaner is used, do not
aim the water jet directly at the bearing points.
Grease all lubricating points after cleaning.

•

Check all moving parts for ease of movement. If
necessary, remove, clean and remount after
regreasing. Replace with new parts if necessary.

Only use original KRONE spare parts.

•

Oil all joints.

•

Thoroughly grease machine.

•

Grease the universal drive shaft guard tubes in order
to prevent freezing.

•

Set down the rotary swather on a dry site. Do not
store near artificial manure.

•

Make good damage to paintwork, thoroughly coat
unpainted parts with anti-corrosion agent.

•

Put the machine on supports to take the pressure off
the tyres, do not let the air out, protect tyres against
sunlight, grease and oil.

•

Make a list of all spare parts required and order in
good time. It is easier for your KRONE to supply and
install spare outside high-season. In addition the
machine is then fully prepared for the coming
summer.

Summary of Contents for Swadro 810

































































Reviews:

No comments