manualshive.com logo in svg

Krone Swadro 810, Operating Instructions Manual, Page: 24 / 64

Share
Download
Krone Swadro 810 Operating Instructions Manual Download Page 24

III - 4

Preparing for Operation

3.3.3 Lighting cable connection

The lighting system is connected via the lighting plug
(1).
Establish the connection between tractor and swather
with the 7-cord cable provided.

•

Connect lighting plug (1) to the lighting socket of the
tractor.

KS102323

KS102327

When inserting the plug, make sure
that plug and socket are clean and dry.
Soiling and moisture can result in
short-circuits!

If neccessary, the permanent power socket
and the holder for the control unit must
first be mounted on the tractor.

•

Connect lighting plug (1) to the lighting socket of the
tractor.

•

Connect plug of the power supply cable (2) to the
permanent power supply socket of the tractor.

When inserting the plug, make sure that
plug and socket are clean and dry. Soiling
and moisture can result in short-circuits!

3.3.4 Connecting the electric control unit

(optional)

The electric control unit connected via the power supply
plug (2).

Summary of Contents for Swadro 810

































































Reviews:

No comments