manualshive.com logo in svg

Krone Swadro 700, Operating Instructions Manual, Page: 44 / 64

Share
Download
Krone Swadro 700 Operating Instructions Manual Download Page 44

VI - 2

Care and maintenance

1

KS-0-034

6

2

3

4

5

6.3

 Tyres

• Installing wheels and tyres requires sufficient knowledge and the availability of proper tools!
• Repair work on the tyres and wheels may only be carried out by specialists using appropriate

tools!

• Set down rotary swather on firm, even ground. Prevent unintended rolling away with wedges.
• Regularly check that wheel nuts are properly seated and tighten if necessary!
• Regularly check air pressure!

Check the tyre pressure at regular intervals (100 h) and
refill if necessary. The values can be found in the
adjacent table.

6.3.2 Wheel fixings

6.3.1 Air pressure

Regularly (50 h) check that wheel nuts are properly
seated and tighten if necessary! The sequence in the
graphic opposite should be observed.

Swadro 700

 Tyres

Tyre pressure

Swadro 800

[bar]

Swadro 900

Single-axle

18 x 8.50 6 PR

1

Tridem-axle

16 x 6.50-8.4 PR

1

Main  chassis

10.0/75-15.3 8 PR

1

The tine screws (1) must be retightened to the specified
tightening torque after they have been used for the first
time.

SW700030

1

Summary of Contents for Swadro 700

































































Reviews:

No comments