3
COMMISSIONING / OPERATION
24
VFC 200
www.krohne.com
06/2019 - 4005059401 - AD VFC200 PB-PA R01 en
Displaying "Single events" currently existing using the VFC 200 PROFIBUS DTM:
Displaying "Single events" currently existing using the VFC 200 PROFIBUS DTM:
Displaying "Single events" currently existing using the VFC 200 PROFIBUS DTM:
Displaying "Single events" currently existing using the VFC 200 PROFIBUS DTM:
Enter Menu "Device
→
Diagnosis
→
Current status messages" to get a detailed view of all "Event
groups" with at least one "Single event" currently existing:
•
Have a look at section "Current status display (click for details)"
•
All "Event groups" with at least one "Single event" currently existing will be displayed
•
A "double-click" on an "Event group" displayed will display all "Single events" (belonging to
this "Event group") currently existing.
Note: A "single-click" on both an "Event group" or an "Single event" will display additional
information within section "Detailed information for selected status"
INFORMATION!
A rough classification of status values according "NE107" is done by using the first character of
the description of a status event:
•
F- / ("F-"): Failure (No measurement possible)
•
S- / ("S-"): Out of specification (Measurements are available but no longer sufficiently
accurate and should be checked)
•
M- / ("M-"): Maintenance required: (Measurements are still accurate but this could change
soon)
•
C- / ("C-"): Function check: (A test function is active; the displayed or transferred measured
value does not correspond to the actual measured value)
•
I- / ("I-"): Information (not defined by NE107 / device specific): (No direct influence on the
measurements)
INFORMATION!
Each diagnosis event defined by UNIT_DIAG_BIT (56) up to UNIT_DIAG_BIT (87) (being contained
Each diagnosis event defined by UNIT_DIAG_BIT (56) up to UNIT_DIAG_BIT (87) (being contained
Each diagnosis event defined by UNIT_DIAG_BIT (56) up to UNIT_DIAG_BIT (87) (being contained
Each diagnosis event defined by UNIT_DIAG_BIT (56) up to UNIT_DIAG_BIT (87) (being contained
in PROFIBUS parameter "DIAGNOSIS_EXTENSION") will be defined as a so called "Event group"
in PROFIBUS parameter "DIAGNOSIS_EXTENSION") will be defined as a so called "Event group"
in PROFIBUS parameter "DIAGNOSIS_EXTENSION") will be defined as a so called "Event group"
in PROFIBUS parameter "DIAGNOSIS_EXTENSION") will be defined as a so called "Event group"
(for detailed information refer to chapter "Status messages and diagnostic information" of the
(for detailed information refer to chapter "Status messages and diagnostic information" of the
(for detailed information refer to chapter "Status messages and diagnostic information" of the
(for detailed information refer to chapter "Status messages and diagnostic information" of the
OPTISWIRL 4200 Handbook). Each "Event group" will consist of up to 32 so called "Single
OPTISWIRL 4200 Handbook). Each "Event group" will consist of up to 32 so called "Single
OPTISWIRL 4200 Handbook). Each "Event group" will consist of up to 32 so called "Single
OPTISWIRL 4200 Handbook). Each "Event group" will consist of up to 32 so called "Single
events". The diagnosis event bit of an "Event group" will be set if at least one "Single event"
events". The diagnosis event bit of an "Event group" will be set if at least one "Single event"
events". The diagnosis event bit of an "Event group" will be set if at least one "Single event"
events". The diagnosis event bit of an "Event group" will be set if at least one "Single event"
belonging to this "Event group" will occur. "Single events" occurred can be displayed by using
belonging to this "Event group" will occur. "Single events" occurred can be displayed by using
belonging to this "Event group" will occur. "Single events" occurred can be displayed by using
belonging to this "Event group" will occur. "Single events" occurred can be displayed by using
the VFC 200 display menu and/or by using the VFC 200 PROFIBUS DTM or the VFC 200
the VFC 200 display menu and/or by using the VFC 200 PROFIBUS DTM or the VFC 200
the VFC 200 display menu and/or by using the VFC 200 PROFIBUS DTM or the VFC 200
the VFC 200 display menu and/or by using the VFC 200 PROFIBUS DTM or the VFC 200
PROFIBUS EDD in conjunction with the appropriate control software (VFC 200 PROFIBUS DTM in
PROFIBUS EDD in conjunction with the appropriate control software (VFC 200 PROFIBUS DTM in
PROFIBUS EDD in conjunction with the appropriate control software (VFC 200 PROFIBUS DTM in
PROFIBUS EDD in conjunction with the appropriate control software (VFC 200 PROFIBUS DTM in
conjunction with PACTware; the VFC 200 PROFIBUS EDD in conjunction with SIMATIC PDM). An
conjunction with PACTware; the VFC 200 PROFIBUS EDD in conjunction with SIMATIC PDM). An
conjunction with PACTware; the VFC 200 PROFIBUS EDD in conjunction with SIMATIC PDM). An
conjunction with PACTware; the VFC 200 PROFIBUS EDD in conjunction with SIMATIC PDM). An
overview of all "Single events" supported by VFC 200 can be found in the VFC 200 Handbook.
overview of all "Single events" supported by VFC 200 can be found in the VFC 200 Handbook.
overview of all "Single events" supported by VFC 200 can be found in the VFC 200 Handbook.
overview of all "Single events" supported by VFC 200 can be found in the VFC 200 Handbook.
