![background image](http://html1.mh-extra.com/html/kramer/afm-20dsp/afm-20dsp_user-manual_2001092072.webp)
Kramer Electronics Ltd.
AFM-20DSP
– Protocol 3000
70
Function
Description
Syntax
Parameters/Attributes
Example
EDID-CS
Set EDID color space.
Set command
might change the
current EDID.
COMMAND
#EDID-CS
input_id
,
ColSpace
<CR>
FEEDBACK
~nn@EDID-CS
input_id
,
ColSpace
<CR><LF>
input_id
– 1
ColSpace
– Color space
0
– RGB
4
– auto
Set HDMI IN 1 EDID color
space to RGB (enabled):
#EDID-CS
1
,
0
<CR>
EDID-CS?
Get EDID color space.
Get command
might change the
current EDID.
COMMAND
#EDID-CS?
input_id
<CR>
FEEDBACK
~nn@EDID-CS
input_id
,
ColSpace
<CR><LF>
input_id
– 1
ColSpace
– Color space
0
– RGB
4
– auto
Get EDID color space:
#EDID-CS?
1
<CR>
ETH-PORT
Set Ethernet port
protocol.
If the port number
you enter is already in
use, an error is
returned.
The port number must
be within the following
range: 0-(2^16-1).
COMMAND
#ETH-PORT
portType
,
ETHPort
<CR>
FEEDBACK
~nn@ETH-PORT
portType
,
ETHPort
<CR><LF>
portType
– TCP/UDP
ETHPort
– TCP/UDP port number
(0
– 65535)
Set the Ethernet port protocol
for TCP to port 12457:
#ETH-PORT
0
,
12457
<CR>
ETH-PORT?
Get Ethernet port
protocol.
COMMAND
#ETH-PORT?
portType
<CR>
FEEDBACK
~nn@ETH-PORT
portType
,
ETHPort
<CR><LF>
portType
– TCP/UDP
0
– TCP
1
– UDP
ETHPort
– TCP / UDP port number (0
– 65535)
Get the Ethernet port protocol
for UDP:
#ETH-PORT?
1
<CR>
FACTORY
Reset device to factory
default configuration.
This command
deletes all user data
from the device. The
deletion can take some
time.
Your device may
require powering off
and powering on for
the changes to take
effect.
COMMAND
#FACTORY
<CR>
FEEDBACK
~nn@FACTORY
OK
<CR><LF>
Reset the device to factory
default configuration:
#FACTORY
<CR>
FEATURE-LIST?
Get feature state
according to the
feature ID.
COMMAND
#FEATURE-LIST?
feature_id
<CR>
FEEDBACK
~nn@FEATURE-LIST
feature_id
,
ir_state
<CR><LF>
Feature_Id
– Feature ID
1
– Maestro
2
– Room Controller
Ir_State
– IR Interface
0
– Disabled
1
– Enabled
Get the room controller feature
state (for the room controller 1):
#FEATURE-LIST?
1
<CR>
HDCP-MOD
Set HDCP mode.
Set HDCP
working mode on the
device input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support
changes following
detected sink -
MIRROR OUTPUT.
When you define
3
as
the mode, the HDCP
status is defined
according to the
connected output in
the following priority:
OUT 1, OUT 2. If the
connected display on
OUT 2 supports
HDCP, but OUT 1
does not, then HDCP
is defined as not
supported. If OUT 1 is
not connected, then
HDCP is defined by
OUT 2.
COMMAND
#HDCP-MOD
inp_id
,
mode
<CR>
FEEDBACK
~nn@HDCP-MOD
inp_id
,
mode
<CR><LF>
inp_id
– Input number:
1
– IN 1 HDMI
2
– IN 2 HDBT
mode
– HDCP mode:
0
– HDCP Off
3
– HDCP defined according to the
connected output
Set the input HDCP-MODE of
IN 1 to Off:
#HDCP-MOD
1
,
0
<CR>
HDCP-MOD?
Get HDCP mode.
Set HDCP
working mode on the
device input:
HDCP supported -
HDCP_ON [default].
HDCP not supported -
HDCP OFF.
HDCP support
COMMAND
#HDCP-MOD?
inp_id
<CR>
FEEDBACK
~nn@HDCP-MOD
inp_id
,
mode
<CR><LF>
inp_id
– Input number:
1
– IN 1 HDMI
2
– IN 2 HDBT
mode
– HDCP mode:
0
– HDCP Off
3
– HDCP defined according to the
connected output
Get the input HDCP-MODE of
IN 1 HDMI:
#HDCP-MOD?
1
<CR>