manualshive.com logo in svg

Kraga Maripi, Build Manual, Page: 18 / 20

Share
Download
Kraga Maripi Build Manual Download Page 18

Electronics

This is by no means the best way possible how to setup your plane. It is just a brief overview of 
possible options.

Motor

To avoid problems when setting correct CG, it is recommended to use motor weighting 110g. You 
should be able to fit inside motors with diameter up to 35mm.

Good option is 

Turnigy Aerodrive SK3 - 3536-1200kv Brushless Outrunner. This motor provides 

plenty of power even for hovering figure.

ESC

If you opted for above mentioned motor option, you need 40A speed controller for brushless motors
ideally with SBEC, for example this one: 

HobbyKing 40A BlueSeries Brushless Speed Controller

.

Battery

Although there is plenty of space in the fuselage, to be able to set correct CG, you have to place 
ESC and Battery next to each other right behind the motor. In this configuration ideal battery weight
is between 120g and 140g. 

Turnigy nano-tech 1500mah 3S 25~50C

 

Lipo Pack

 is one of many 

options.

Receiver

This depends on your transmitter. Only requirement is to have 5 channels.

[email protected]

Summary of Contents for Maripi





















Reviews:

No comments